Using Cherry for Woodworking Projects
CHERRY (botanically called "black" cherry, Prunus serotina) has long been ranked second only to walnut by makers of finely crafted furniture. Once you've worked it, you'll understand why: great color, fine grain, a wonderful luster, and it even smells good.
History in Woodworking
Look to the 1950s for the beginning of cherry's popularity as a furniture wood. Mass-produced cherry furniture took its place alongside finned autos, rec rooms, and brick barbecue grills in that new era of mass consumption.
A century or more prior to Shaker craftsmen's use of cherry for their beautifully simple chairs, chests, cabinets, tables, and accessories, the wood had been substituted for Cuban mahogany by Colonial furniture makers. When darkened by stain or age, cherry looked just like the expensive import.
Much later, cherry was the popular choice for paneling in elegant railroad passenger cars and the trim in expensive horse-drawn carriages.Cherry still ranks near the top with today's American furniture makers.
It's also among the high-end options for kitchen cabinetry, architectural paneling (as veneer) and Fortune 500-grade office furniture.
Where the wood comes from
Cherry grows throughout the eastern half of the United States, with the largest trees in the Appalachian and Allegheny mountains of Pennsylvania and New York.
What you'll pay
On average, a board foot of 4/4 FAS, flatsawn cherry lumber surfaced on two sides (S2S) costs about $5. Wide and thick stock is available at higher prices. Curly and other figured stock will cost double that of plain. Veneer sells at $2 per square foot more for figured sheets. And you can expect to pay $100 for an A2-grade sheet of 3/4" veneer-core cherry plywood.
Choose top-quality wood
As with all highly desirable furniture woods, the logs with the fewest defects become veneer. So even the highest grade cherry lumber can display bands of light-colored sapwood as well as dark gum pockets. That's why it's important to be picky: Check for color. A board with one face displaying all clear
heartwood may look quite different when turned over. Also, because cherry's color varies
from light brown to pink, matching color can be challenging. Stand boards next to each other to check for uniformity. And keep in mind that cherry will darken to a mahoganylike reddish brown.
Limit gum pockets. Try as you might, gum pockets prove difficult to avoid (see the photo below). Lumber graders don't see these dark spots and streaks as defects in small quantities, but you should seek boards with the fewest.
Minimize knots. Knots aren't a real problem because the highest graded boards have few. Be sure, though, that they're small and tight.
Looking for figured stock? Your chances of finding some from other than a specialty wood dealer are slim. However, quartersawn and riftsawn boards can display ray flecks and even curly figure. Occasionally, a fiddleback-type figure occurs, too.
Working Cherry in the Shop
You'll find that cherry works well with sharp hand tools. With power tools (sharp cutting edges here, too), be aware of the wood's tendency to burn. To avoid it, follow these tips:
Ripping and routing: Use your sharpest blades and bits, and maintain a steady feed rate (slowing down causes the edge to heat up). You also can cut the stock wide, then use your jointer to clean up the sawn edge. With a router, take off wood in light passes.
Removing burn marks: Use 100- or 120-grit sandpaper, or a hand scraper, to get rid of them. Stubborn ones require dampening with mineral spirits to soften the area before removal with a hand scraper.
Sanding cherry: Because cherry has a tight grain and is hard, don't skip a grit or you'll leave tiny scratches that show under a fi nish. Sand the faces through 180 grit. For end grain, sand through 220 grit to burnish the wood if it's going to be stained or finish-coated.
When it comes to removing glue squeeze-out, get fussy. Glue spots not completely removed will stand out.
Deciding on the right finish
Cherry is easy enough to work. Finishing is another story. That's because new cherry simply doesn't look like old.
To obtain the darkened hue of aged cherry, most woodworkers turn to stain. But cherry doesn't take stain well. It often blotches. And even if you achieve a pleasing, uniform color, age will darken it.
If you've selected your cherry boards for matching color, you've won half the battle. Simply apply a clear film finish (or oil-varnish blend) and let nature take its course. Or, you can tone a sprayed finish, such as lacquer, with dye or pigment. If you feel you must stain, use a non-penetrating one. (A gel stain works best, but so will aniline dye if you're willing to experiment.) No matter how you color the wood, don't be heavy-handed.
Information for this article is sourced by permission of Woodcraft.
More Woodworking Projects
For the Woodworker who has everything, give the gift of choice with a Rockler Gift Card!